PCB of my broken USB harddisk

I was impressed you have the PCB of my broken USB harddisk.

However, I can see the disk startup in Linux dmesg, and I hear the disk spinning. In the dmesg output, I get the warning “Read Capacity(10) failed: Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE”.

Would it be usefull to order this PCB?

Or would it be the configuration RAM that is corrupted? Or some other kind of BIOS failure?

Any help is greatly appreciated!

Here the whole DMESG log:

[di jul  4 23:26:59 2023] usb 3-2: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd

[di jul  4 23:26:59 2023] usb 3-2: New USB device found, idVendor=1058, idProduct=1048, bcdDevice=10.22

[di jul  4 23:26:59 2023] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=5

[di jul  4 23:26:59 2023] usb 3-2: Product: Elements 1048

[di jul  4 23:26:59 2023] usb 3-2: Manufacturer: Western Digital

[di jul  4 23:26:59 2023] usb 3-2: SerialNumber: 575838314135334D38313634

[di jul  4 23:27:00 2023] usb-storage 3-2:1.0: USB Mass Storage device detected

[di jul  4 23:27:00 2023] scsi host4: usb-storage 3-2:1.0

[di jul  4 23:27:00 2023] usbcore: registered new interface driver usb-storage

[di jul  4 23:27:00 2023] usbcore: registered new interface driver uas

[di jul  4 23:27:01 2023] scsi 4:0:0:0: Direct-Access     WD       Elements 1048    1022 PQ: 0 ANSI: 6

[di jul  4 23:27:01 2023] scsi 4:0:0:0: Attached scsi generic sg2 type 0

[di jul  4 23:27:01 2023] sd 4:0:0:0: [sdc] Spinning up disk…

[di jul  4 23:27:02 2023] ……………………………………………………………………………………..not responding…

[di jul  4 23:28:53 2023] sd 4:0:0:0: [sdc] Read Capacity(10) failed: Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE

[di jul  4 23:28:53 2023] sd 4:0:0:0: [sdc] Sense Key : Not Ready [current] 

[di jul  4 23:28:53 2023] sd 4:0:0:0: [sdc] Add. Sense: Logical unit is in process of becoming ready

[di jul  4 23:28:53 2023] sd 4:0:0:0: [sdc] 0 512-byte logical blocks: (0 B/0 B)

[di jul  4 23:28:53 2023] sd 4:0:0:0: [sdc] 0-byte physical blocks

[di jul  4 23:28:55 2023] sd 4:0:0:0: [sdc] Test WP failed, assume Write Enabled

[di jul  4 23:28:57 2023] sd 4:0:0:0: [sdc] Asking for cache data failed

[di jul  4 23:28:57 2023] sd 4:0:0:0: [sdc] Assuming drive cache: write through

[di jul  4 23:28:57 2023] sd 4:0:0:0: [sdc] Spinning up disk…

[di jul  4 23:28:58 2023] ……………………….not responding…

[di jul  4 23:31:32 2023] sd 4:0:0:0: [sdc] tag#0 timing out command, waited 60s

[di jul  4 23:32:01 2023] usb 3-2: USB disconnect, device number 2

[di jul  4 23:32:01 2023] xhci_hcd 0000:00:14.0: WARN Set TR Deq Ptr cmd failed due to incorrect slot or ep state.

[di jul  4 23:32:01 2023] sd 4:0:0:0: [sdc] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK

[di jul  4 23:32:01 2023] sd 4:0:0:0: [sdc] Sense not available.

[di jul  4 23:32:01 2023] sd 4:0:0:0: [sdc] Attached SCSI disk

Replacement the PCB will not solve the problem below.

    * The drive will power up normally (no ticking noises, errors etc) but will not be recognized by the computer

    * The drive will power up normally and be recognized correctly but will report a size of 0 bytes

    * The drive will power up but report SMART errors on boot

Those problem is caused by the HDD firmware corrupted.You can find a data recovery company help.